首页/ 题库 / [单选题]What OSPF command, w的答案

What OSPF command, when configured, will include all interfaces into area 0?（）

单选题
2022-01-01 12:36
A、network 0.0.0.0 255.255.255.255 area 0
B、network 0.0.0.0 0.0.0.0 area 0
C、network 255.255.255.255 0.0.0.0 area 0
D、network all-interfaces area 0
查看答案
正确答案
A
试题解析
标签： CCNA(200-120)
感兴趣题目
When sending an LCP Configuration Request, what can the ERX Edge Router possibly negotiate?（）
Refer to the exhibit. OSPF is configured on all routers in the network. Area 5 is configured as an NSSA areA. The RIPv2 routes are redistributed into the OSPF domain on router R5. What two types of LSAs will be originated by router R5?（）
Refer to the exhibit. OSPF is configured on all routers in the network. Area 5 is configured as an NSSA areA. The RIPv2 routes are redistributed into the OSPF domain on router R5. What two types of LSAs will be originated by router R5?（）
What is the correct sequence of commands to configure and verify SRM with SSO redundancy? （）
Which configuration command configures IS-IS to support MPLS Traffic Engineering?（）
Which two commands would you use to view OSPF routes?（）
What are two commands that can be used to configure MBGP for multicast?（）

A CCNA candidate is working on a 2600 Cisco router. The person needs to verify that the configuration register is set to boot the router IOS from flash memory and use the commands saved in the startup-configuration file.
Which command will display this information, and what is the configuration register value that should be displayed?（）
What happens when Host Checker is configured to perform checks every "0" minutes? （）
What is the purpose of the OSPF router ID in a OR/BOR election?（）
As a candidate for CCNA examination， when you are familiar with the basic commands， if you input thecommand "enable secret level 5 password" in the global mode ， what does it indicate？（）
The third officer’s duty is to（）when vessel is commanded under the pilot or captain.
相关题目
What must be set correctly when configuring a serial interface so that higher-level protocols calculate the best route?（）
What OSPF command, when configured, will include all interfaces into area 0?（）
Which commands are required to properly configure a router to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）
What are three key concepts that apply when configuring the EIGRP stub routing feature in a hub and spoke network？（）
An administrator types in the command router ospf 1 and receives the er ror message: "OSPF process 1 cannot start." (Output is omitted.) What should be done to correctly set up OSPF？（）
The Testking network has been configured with OSPF as the routing protocol.What is the default administrative distance of the OSPF routing protocol?（）
When implementing OSPFv3, which statement describes the configuration of OSPF areas?（）
What is the default configuration file used by the sendmail command?（）
When configuring a serial interface on a router, what is the default encapsulation?（）
You need to configure an 802.1Q link on a Ezonexam switch. Which commands, when used together, would do this? (Select two answer choices)
When policy - based routing (PBR) is being configured, which three criteria can the set command specify?（）

Refer to the exhibits. You are verifying your OSPF implementation, and it does not seem to be functioning properly. What can you conclude from the exhibit and the show running - configuration command output? （）
When the Cisco IOS OSPF command ip ospf dead-interval minimal hello-multiplier 5 is configured， which two statements are true？ （）
An OSPF interface has been configured with the bandwidth 64 command. What will be the calculated OSPF cost of this link?（）
EIGRP has been configured to opera te over Frame Relay multipoint connections. What should the bandwidth command be set to?（）
When you issue the logging trap informational command, what happens? （）
OSPF routing uses the concept of areas. What are the characteristics of OSPF areas?（）
OSPF routing uses the concept of areas. What are the characteristics of OSPF areas?（）
Which command will delete the current rescue configuration?（）
When sending an LCP Configuration Request,what can the ERX Edge Router possibly negotiate?（）
广告位招租WX:84302438
题库考试答案搜索网

免费的网站请分享给朋友吧

题库考试答案搜索网 2022 ©

关于我们网站声明合作共赢