首页/ 题库 / [单选题]VE1 is a switch in t的答案

VE1 is a switch in the Ezonexam network. Why will VE1 never learn the broadcast address?

单选题
2022-01-04 07:56
A、Broadcast frames are never sent to switches
B、A broadcast frame. is never forwarded by a switch
C、Broadcasts only use network layer addressing
D、A broadcast address will never be the source address of a frame
E、Broadcast addresses use an incorrect format for the switching table
F、None of the above
查看答案
正确答案
D
试题解析
D
标签：
感兴趣题目
The LAN needs are expanding at the Ezonexam corporate office, which is quickly growing. You are instructed to enlarge the area covered by a single LAN segment on the Ezonexam network.
Which three statements are true about the operation of a full-duplex Ethernet network, which is being used in the Ezonexam LAN? (Choose three)
Both bridges are switches are being used throughout the Ezonexam LAN. Which of the following statements are true regarding bridges and switches in this network?
While troubleshooting an issue in the Ezonexam LAN you notice that a network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interface port?
A new switch is installed in the Ezonexam network. This switch is to be configured so that VLAN information will be automatically distributed to all the other Cisco Catalyst switches in the network.
You need to decide on which trunking method to implement in the Ezonexam network. What is a characteristic of ISL and 802.1q frame. tagging in a switched LAN environment?
Which two statements describe the operation of the CSMA/CD access method, which is in use on the Ezonexam network? (Choose two)
Why might the Ezonexam network administrator set the configuration register to 0x2142 on a 2600 series Cisco router?
In broadcast network the first adj of ospf is 2-way？why？this question will give you a picture.
What will a new Ezonexam router do during startup if a configuration file is not located in NVRAM?
At which OSI layer is a logical path created between two host systems named VE1 and VE2 on the Ezonexam LAN?
The Ezonexam network administrator needs to verify that switch interface 0/5 has been assigned to the Marketing VLA.N. Which command will accomplish this task?
相关题目
Why will a switch never learn a broadcast address?（）
Why will a switch never learn a broadcast address（）。
Why is QoS important in a converged network?（）
A new Ezonexam switch is installed into an existing LAN and a new VTP trunk is set up with an existing switch. Which VLANs will be allowed on this new trunk?
The purpose of a network（ ）is to provide a shell around the network which will protect the system connected to the network from various threats.
A new switch is being installed in the Ezonexam network and you have been assigned the task of connecting it to an existing switch. In doing this, you want to set up the VLAN Trunking Protocol so that VLAN information can be passed between the switches. Which of the following must you do to accomplish this? (Choose all that apply).
The network security policy for Ezonexam requires that only one host be permitted to attach dynamically to each switch interface. If that policy is violated, the interface should be automatically disabled. Which two commands must the Ezonexam network administrator configure on the 2950 Catalyst switch to meet this policy? (Choose two)
VE1 is a switch in the Ezonexam network. Why will VE1 never learn the broadcast address?
The Ezonexam network administrator needs to determine what LAN devices to install on the Ezonexam network. What are two advantages of using Layer 2 Ethernet switches over hubs? (Choose two)
The Ezonexam network administrator wants to use a router named VE1 to segment the local network. What are some of the advantages of using VE1 to segment the network? (Choose two)
You need to perform. some initial configuration tasks on a new Ezonexam switch. What is the purpose of assigning an IP address to a switch?
As a network administrator, you have configured a Catalyst 6500 Series Switch with redundant supervisor engine in a CIS network. What is the result of issuing the redundancy force-switchover command on that switch?（）
The network administrator has discovered that the power supply has failed on a switch in the company LAN and that the switch has stopped functioning. It has been replaced with a Cisco Catalyst 2950 series switch. What must be done to ensure that this new switch becomes the root bridge on the network?（）
The network administrator has discovered that the power supply has failed on a switch in the company LAN and that the switch has stopped functioning. It has been replaced with a Cisco Catalyst 2950 series switch.What must be done to ensure that this new switch becomes the root bridge on the network?（）
A Ezonexam Ethernet switch receives a unicast frame. with a destination MAC that is listed in the switch table. What will this switch do with the frame?
What will an Ethernet switch do if it receives a unicast frame with a destination MAC that is listed in the switch table（）。
The switched LAN is displayed below： In this network， STP has been implemented. Switch SW1 is the root switch for the default VLAN.To reduce the broadcast domain， the network administrator decides to split users on the networkinto VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 rootprimary on switch SW1. What will happen as a result of this change？（）
The switched LAN is displayed below： In this network， STP has been implemented. Switch SW1 is the root switch for the default VLAN.To reduce the broadcast domain， the network administrator decides to split users on the networkinto VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 rootprimary on switch SW1. What will happen as a result of this change？（）
In a switched LAN network, what is the Spanning-Tree algorithm used for?（）
In a switched LAN network, what is the Spanning-Tree algorithm used for?
广告位招租WX:84302438
题库考试答案搜索网

免费的网站请分享给朋友吧

题库考试答案搜索网 2022 ©

关于我们网站声明合作共赢