首页/ 题库 / [单选题]Which configuration 的答案

Which configuration command configures IS-IS to support MPLS Traffic Engineering?()

单选题
2022-06-14 03:08
A、metric-style wide
B、redistribute mpls
C、metric-style narrow
D、dynamic-redistribute
查看答案

正确答案
A

试题解析

标签: CMS专题
感兴趣题目
Which of the following commands would you use, to configure a default route to any destination NOT found in the routing table?()
Which command will delete the current rescue configuration?()
When a DHCP server is configured, which two IP addresses should never be assignable to hosts?()
What is the correct sequence of commands to configure and verify SRM with SSO redundancy? ()

You have enabled backup optimization in RMAN. You issue the following RMAN command to configure a redundancy-based retention policy:
CONFIGURE RETENTION POLICY TO REDUNDANCY 3;
Which statement is true?()

Which command would you configure globally on a Cisco router that would allow you to view directly connected Cisco devices?()
Which configuration command configures IS-IS to support MPLS Traffic Engineering?()
Which two commands would you use to discard a candidate configuration?()

A CCNA candidate is working on a 2600 Cisco router. The person needs to verify that the configuration register is set to boot the router IOS from flash memory and use the commands saved in the startup-configuration file.
Which command will display this information, and what is the configuration register value that should be displayed?()

A 2-way interleaved DDR configuration and a 4-way interleaved SDRAM configuration will produce which of the following?()
Which of the following is the only place where initial boot settings can be configured?()

Router R1 uses S0/0 to connect via a T/1 to the Frame Relay servicE. Five PVCs terminate on the serial link. Three PVCs (101, 102, and 103) are configured on subinterface S0/0.1, and one each (104 and 105) are on S0/0 .2 and S0/0.3. The configuration shows no configuration related to EIGRP WAN bandwidth control, and the bandwidth command is not configured at all.
Which of the following is true about how IOS tries to limit EIGRP's use of bandwidth on S0/0?()

相关题目
Which command would you configure globally on a Cisco router that would allow you to view directly connected Cisco devices?()
Which of the following is a correct statement about how the user environment is configured at login?()
ABR R1 has been configured with an area 1 stub no - summary command. Which stubby area type is area 1?()
Which commands are required to properly configure a router to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?()
Which procedure should be used to configure the system to prevent all users from using the ‘at’ command?()
You work as a technician at TestKing. You are configuring a Cisco router. You want to configure the IP address on an interface.Which command should you use?()
A group of stars which appear close together and form a striking configuration such as a person or animal is a().
Which of the commands below can you use to configure a default route?()
You need to configure a default route on a Ezonexam router. Which command will configure a default route on a router?
Which command will configure a default route on a router?()
What is the default configuration file used by the sendmail command?()
Which command is used to configure a default route?()
When policy - based routing (PBR) is being configured, which three criteria can the set command specify?()
When the Cisco IOS OSPF command ip ospf dead-interval minimal hello-multiplier 5 is configured, which two statements are true? ()

LPAR1 is configured to have the same 2 LUNs virtualized by a redundant pair of VIO servers.
Which command will validate thatboth storage paths are available?()

Which dose the frame-relay interface-dlci command configure?()
Which three of the following protocols will be forwarded to a host specified by the ip helper - address interface configuration command if the configuration has not been modified by the ip forward - protocol udp global con figuration command?()
Which dose the frame-relay interface-dlci command configure?()
The TestKing.com administrator has made changes to the router configuration but cannot remember if those changes were saved. Which of the following commands allows the administrator to see the configuration that will load when the router is restarted?()
Which of the commands below would you enter if you wanted to see the configuration register of your router?()
广告位招租WX:84302438

免费的网站请分享给朋友吧