VLAN 3 is not yet configured on your switch.What happens if you set the switchport access vlan 3 commmand interface configuration mode?（） -题库考试答案搜索网

VLAN 3 is not yet configured on your switch.What happens if you set the switchport access vlan 3 commmand interface configuration mode?（）

单选题

2022-01-14 22:06

A、The command is accepted and the respective VLAN is added to vlan dat.
B、The command is rejected.
C、The command is accepted and you must configure the VLAN manually.
D、The port turns amber.

查看答案

正确答案

试题解析

标签： CCNA(640-802)

感兴趣题目

设x=4，y=8，z=7，以下表达式的值是 x＜y And (Not y＞z) Or z＜x

Once the port has been named and accepted by，or on behalf of，the Shipowner，he can not afterwards refuse to go（）__ on the ground that it is not safe.

A CCNA candidate is working on a 2600 Cisco router. The person needs to verify that the configuration register is set to boot the router IOS from flash memory and use the commands saved in the startup-configuration file.
Which command will display this information, and what is the configuration register value that should be displayed?（）

The Shipowner must not stow goods on deck（）there is a trade usage to that effect or the Charterer has given his express or implied consent.

Line l passes through the origin and is perpendicular to the line given by the equation 2x + y = 8. Which of the following points is NOT on line l?

Which of the following is an OSPF configuration parameter that is used on an ABR, but not on an internal router？（）

If you do not know the subject, you will not understand what is said or written, even if English is your mother （） what is said or written.

The declaration made by the shipper，if embodied in the bill of lading，is（）evidence，but is not binding or conclusive on the carrier.

Each of these vlans has one host each on its port SVI on vlan 1 - ip 192.168.1.11 with snm Switch B - Ports 3， 4 connected to ports 3 and 4 on Switch A Port 15 connected to Port on Router. Tasks to do 1. Use non proprietary mode of aggregation with Switch B being the initiator -- Assumed use LACP with B being in Active mode 2. Use non proprietary trunking and no negotiation -- Assumed use switchport mode trunk and switchport trunk encapsulation dot1q 3. Restrict only to vlans needed -- Assumed either vtp pruning or allowed vlan list. vtp pruning command did not seem to work on the simulator so landed using allowed vlan list 4. SVI on vlan 1 with some ip and subnet given 5. Configure switch A so that nodes other side of Router C are accessible -- Assumed this to mean that on switch A default gatway has to be configured. 6. Make switch B the root -- Could not get this to work. Exam hung when I tried the command spanning-tree vlan 1，21-23 priority 4096

Exhibit：

Assuming that VLAN 1 and VLAN 2 traffic is enabled on the above network， what effect will thefollowing command have when entered on port 0/2 on switch SWA？（） spanning-tree vlan 1 port-priority 16

Router R1 uses S0/0 to connect via a T/1 to the Frame Relay servicE. Five PVCs terminate on the serial link. Three PVCs (101, 102, and 103) are configured on subinterface S0/0.1, and one each (104 and 105) are on S0/0 .2 and S0/0.3. The configuration shows no configuration related to EIGRP WAN bandwidth control, and the bandwidth command is not configured at all.
Which of the following is true about how IOS tries to limit EIGRP's use of bandwidth on S0/0?（）

●设AND、OR和NOT分别表示按位与、按位或和按位求反运算，且X=10011011，Y=01111010，Z=11101000，则(NOT(X) AND Y)= (9) ， (Y OR NOT(Z))= (10) 。10011011011110101110100001100000(10)