首页/ 题库 / [单选题]A Cisco router has b的答案

A Cisco router has been configured with the following command:IP nat pool nat-test 192.168.6.10 192.168.6.20 netmask 255.255.255.0his is an example of what type of NAT?（）

单选题
2022-06-28 22:00
A、Static NAT
B、Dynamic NAT
C、Dynamic NAT with overload
D、Port Address Translation
E、None of the above
查看答案
正确答案
B
试题解析
标签： CCNA(640-801)
感兴趣题目
What is the reason for configuring a passive interface on a router?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（） ipv6 router eigrp 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000::1/64 ipv6 eigrp 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 eigrp 1
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（） ipv6 unicast- routing interface f0/0 ipv6 rip one enable ipv6 address 2000::1/64 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 rip one enable
Which command would you configure globally on a Cisco router that would allow you to view directly connected Cisco devices?（）
Customer X has a hub-and-spoke Frame Relay network， with a central office and two branch offices（RemoteA and RemoteB）. Each location has only one physical link to the Frame Relay cloud and RemoteB has a router that is not a Cisco router. Since the installation，there is no connectivity between RemoteB and the central office. What is a possible solution to this issue？（）
Why might the Ezonexam network administrator set the configuration register to 0x2142 on a 2600 series Cisco router?

A CCNA candidate is working on a 2600 Cisco router. The person needs to verify that the configuration register is set to boot the router IOS from flash memory and use the commands saved in the startup-configuration file.
Which command will display this information, and what is the configuration register value that should be displayed?（）
How can a Ezonexam administrator determine if a router has been configured when it is first powered up?
Refer to the exhibit. In this network， R1 has been configured to advertise a summary route， 192.168.0.0/22， to R2. R2 has been configured to advertise a summary route， 192.168.0.0/21， to R1. Both routers have been configured to remove the discard route （the route to null created when a summary route is configured） by setting the administrative distance of the discard route to 255.What will happen if R1 receives a packet destined to 192.168.3.1？（）
A Cisco router has been configured with the following command:IP nat pool nat-test 192.168.6.10 192.168.6.20 netmask 255.255.255.0his is an example of what type of NAT?（）
A new trunk has been configured on a switch in the Ezonexam LAN. By default, which VLANs are allowed over this trunk link?
What is a new feature of the Cisco ISR router? （）
相关题目
A new network has been configured using OSPF as the routing protocol. With which network type will OSPF establish router adjacencies but not perform the DR/BDR election process?（）
If A small business customer has more sophisticated needs, which Cisco router portfolio would be the best choice?（）
If A small business customer has more sophisticated needs, which Cisco router portfolio would be the best choice?（）
Which command would you configure globally on a Cisco router that would allow you to view directly connected Cisco devices?（）
Which encapsulation types are configurable on a Cisco switch for a trunk?（）
Which commands are required to properly configure a router to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）
Which parameter or parameters are used to calculate OSPF cost in cisco routers?（）
You work as a technician at TestKing. You are configuring a Cisco router. You want to configure the IP address on an interface.Which command should you use?（）
You are about to configure PPP n the interface of a Cisco router. Which authentication methods could you use?（）

A Cisco router has been configured, and the copy running-config startup-config command has been issued. When the router is power cycled, the router prompts with:
"Would you like to enter the initial configuration dialog? [yes/no]"
Why has this occurred?（）
You just purchased a refurbished router that contains a configuration from a previous deployment. What should you do, before entering a new configuration into the router?（）
How can an administrator determine if a router has been configured when it is first powered up?（）
Which of the following Frame-Relay encapsulation commands would you use, if you had to connect your Cisco router to a non-Cisco router?（）
You need to configure a default route on a Ezonexam router. Which command will configure a default route on a router?
Which command will configure a default route on a router?（）
When configuring a serial interface on a router, what is the default encapsulation?（）
What is the default configuration register setting on most Cisco routers?
A medium-sized company has a Class C IP address. It has two Cisco routers and one non-Cisco router. All three routers are using RIP version 1. The company network is using the block of 198.133.219.0/24. The company has decided it would be a good idea to split the network into three smaller subnets and create the option of conserving addresses with VLSM. What is the best course of action if the company wants to have 40 hosts in each of the three subnets?（）
There are three routers on a Gigabit Ethernet LAN: Router A, Router B, and Router C. Router A is the Designated Intermediate System (DIS) at Level 1 for that LAN. Router A's DIS priority is 64. The LAN is a Level 1-only link. Router D has just been powered up on that same LAN and its DIS priority is 80. Which statement is true?（）
A network administrator needs to configure a router for a Frame Relay connection to a non-Cisco router. Which of the following commands will prepare the WAN interface for this connection?（）
广告位招租WX:84302438
题库考试答案搜索网

免费的网站请分享给朋友吧

题库考试答案搜索网 2022 ©

关于我们网站声明合作共赢